Vivotek MDR-10-12 10W Single Output Industrial DIN Rail Power Supply,

MDR-10-12: 10W Single Output Industrial DIN Rail Power Supply, 12V, 85~264VAC In, 12VDC/10W Out , – 20 ℃ ~ 70 ℃, 3 Year Warranty, Supports: AW-IHS-0200,AW-IHS-0201,AW-IHS-0203

Technical Specification

OUTPUT

DC VOLTAGE: 12V
RATED CURRENT: 0.84A
CURRENT RANGE :0 ~ 0.84A
RATED POWER: 10W
RIPPLE & NOISE (max.) Note.2: 120mVp-p
VOLTAGE TOLERANCE Note.3: ±3.0%
LINE REGULATION: ±1.0%
LOAD REGULATION: ±3.0%
SETUP, RISE TIME Note.5: 500ms, 30ms/230VAC 1000ms, 30ms/115VAC at full load
HOLD UP TIME (Typ.): 120ms/230VAC 25ms/115VAC at full load

INPUT

VOLTAGE RANGE: 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE: 47 ~ 63Hz
EFFICIENCY (Typ.): 81%
AC CURRENT (Typ.): 0.33A/115VAC 0.21A/230VAC
INRUSH CURRENT (Typ.): COLD START 35A/115VAC 70A/230VAC
LEAKAGE CURRENT: <1mA / 240VAC

PROTECTION

OVERLOAD:
Above 105% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
OVER VOLTAGE:
13.8 ~ 16.2V
Protection type : Shut down o/p voltage, re-power on to recover

FUNCTION

DC OK ACTIVE SIGNAL (max.): 9 ~ 13.5V / 40mA

ENVIRONMENT

WORKING TEMP.: -20 ~ +70℃ (Refer to “Derating Curve”)
WORKING HUMIDITY: 20 ~ 90% RH non-condensing
STORAGE TEMP., HUMIDITY: -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT: ±0.03%/℃ (0 ~ 50℃)
VIBRATION: Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6

SAFETY & EMC (Note 4)

SAFETY STANDARDS: UL508, TUV EN60950-1 approved
WITHSTAND VOLTAGE: I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC
ISOLATION RESISTANCE: I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
EMC EMISSION: Compliance to EN55011, EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3
EMC IMMUNITY: Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024,EN61000-6-1,EN61204-3, light industry level, criteria A

OTHERS

MTBF: 584K hrs min. MIL-HDBK-217F (25℃)
DIMENSION: 22.5*90*100mm (W*H*D)
PACKING: 0.17Kg; 72pcs/13.2Kg/0.91CUFT

NOTE

1. All parameters NOT Specially mentioned are measured at 230VAC input, rated load and 25 °C of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor
3. Tolerance: includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI” testing of component power supplies.”
5. Length of set up time is measured at cold first start. Turning ON/OFF power supply may lead to increase to the set up time.